← Paper airplane lessons

Learning Center

Cut-tail Glider

Cut a fuselage, main wing, horizontal tail and vertical fin, then join them as a conventional tail assembly.

Loading 3D preview…

YOUR PAPER AIRPLANE

Cut-tail Glider

Cut and join a body, main wing, flat tail and upright fin.

  • 1 US Letter sheet215.9 × 279.4 mm · 75 g/m²
  • 3 guided stepsruler + pencil · scissors · tape for assembly
  • 6 numbered paper parts5 documented joins · follow the construction drawings

Experimental 3D guide. FlightHub has not physically tested this pattern’s folding or flight.

Cut sheets and joining dimensions

The 3D view is not a cutting template. These drawings give nominal outlines and joining coordinates in millimeters; they resize to fit this screen. The coordinates are software-checked, but physical fit and a learner-tested join order are unverified.

For an offline copy and standalone SVG files, keep this design in Studio and download its guide. If printing cut sheets, use 100% size and measure the 50 mm scale bar before cutting. Print scale, paper fit, joint strength and flight remain physically unverified.

Dimensioned construction · recipe 1.1.0

6 parts on 1 checked US Letter sheet. Each cut outline is a rigid unfolding of the same part shown in the assembly. Dimensions are nominal geometric targets; paper thickness, tape, joint fit and strength remain unverified. No calibrated slot width or flight setting is specified.

Use the separate SVG cut-sheet files at 100% size and measure their 50 mm bars. Part views and assembly views below may be enlarged; use their written dimensions and coordinates.

PartRoleSheetCut bounds (mm)
P1 tail-bodybody116, 250
P2 tail-main-leftmain-wing182.152, 60.802
P3 tail-main-rightmain-wing182.152, 60.802
P4 tailplane-lefttail128.16, 24.858
P5 tailplane-righttail128.16, 24.858
P6 vertical-finfin130, 28
Full-size cut sheet 1 · verify print scale
Cut sheet 1 of 1: cut-tail-glider / 1.1.0P1P2P3P4P5P650 mm scale check — print at 100%, measure before cuttingcut-tail-glider / 1.1.0 / sheet 1

Part outlines and measured vertices

For each part, mark vertex 1, then the remaining local (u, v) coordinates in millimeters and join them in numbered order. The edge lengths are a cross-check; the bounding rectangle alone is not the part shape.

P1 tail-body — dimensions in millimeters123416 mm250 mm

P1 tail-body

Local cut vertices (u, v), mm: 1: (0, 0); 2: (16, 0); 3: (16, 250); 4: (0, 250).

Edges in vertex order, mm: 16, 250, 16, 250.

Assembly vertices (x, y, z), mm: 1: (-8, 0, 0); 2: (8, 0, 0); 3: (8, 250, 0); 4: (-8, 250, 0).

P2 tail-main-left — dimensions in millimeters123482.152 mm60.802 mm

P2 tail-main-left

Local cut vertices (u, v), mm: 1: (0, 0); 2: (82.152, 0); 3: (70.832, 60.802); 4: (3.347, 54.898).

Edges in vertex order, mm: 82.152, 61.847, 67.742, 55.

Assembly vertices (x, y, z), mm: 1: (-8, 110, 0); 2: (-87.206, 115, 21.223); 3: (-72.717, 175, 17.341); 4: (-8, 165, 0).

P3 tail-main-right — dimensions in millimeters123482.152 mm60.802 mm

P3 tail-main-right

Local cut vertices (u, v), mm: 1: (0, 0); 2: (82.152, 0); 3: (70.832, 60.802); 4: (3.347, 54.898).

Edges in vertex order, mm: 82.152, 61.847, 67.742, 55.

Assembly vertices (x, y, z), mm: 1: (8, 110, 0); 2: (87.206, 115, 21.223); 3: (72.717, 175, 17.341); 4: (8, 165, 0).

P4 tailplane-left — dimensions in millimeters123428.16 mm24.858 mm

P4 tailplane-left

Local cut vertices (u, v), mm: 1: (0, 0); 2: (28.16, 0); 3: (24.538, 22.514); 4: (2.663, 24.858).

Edges in vertex order, mm: 28.16, 22.804, 22, 25.

Assembly vertices (x, y, z), mm: 1: (-8, 225, 0); 2: (-36, 228, 0); 3: (-30, 250, 0); 4: (-8, 250, 0).

P5 tailplane-right — dimensions in millimeters123428.16 mm24.858 mm

P5 tailplane-right

Local cut vertices (u, v), mm: 1: (0, 0); 2: (28.16, 0); 3: (24.538, 22.514); 4: (2.663, 24.858).

Edges in vertex order, mm: 28.16, 22.804, 22, 25.

Assembly vertices (x, y, z), mm: 1: (8, 225, 0); 2: (36, 228, 0); 3: (30, 250, 0); 4: (8, 250, 0).

P6 vertical-fin — dimensions in millimeters12330 mm28 mm

P6 vertical-fin

Local cut vertices (u, v), mm: 1: (0, 0); 2: (30, 0); 3: (30, 28).

Edges in vertex order, mm: 30, 28, 41.037.

Assembly vertices (x, y, z), mm: 1: (0, 220, 0); 2: (0, 250, 0); 3: (0, 250, 28).

Assembly views and join stations

Assembly coordinates in millimeters: x left/right, y rearward from the body nose (or the shown center datum), z up. Cut drawings use their own numbered vertex coordinates. Match the listed edge or overlap endpoints. Tape tabs join those locations; the layout does not prescribe an adhesive product, tape size or verified load capacity.

top assembly view
top assembly view — nominal millimeter geometryP1P2P3P4P5P6J1J2J3J4J5
front assembly view
front assembly view — nominal millimeter geometryP1P2P3P4P5P6J1J2J3J4J5
side assembly view
side assembly view — nominal millimeter geometryP1P2P3P4P5P6J1J2J3J4J5
JoinPartsMethodEndpoint A (x, y, z), mmEndpoint B (x, y, z), mm
J1P1 tail-body / P2 tail-main-lefttape-edge-8, 110, 0-8, 165, 0
J2P1 tail-body / P3 tail-main-righttape-edge8, 110, 08, 165, 0
J3P1 tail-body / P4 tailplane-lefttape-edge-8, 250, 0-8, 225, 0
J4P1 tail-body / P5 tailplane-righttape-edge8, 250, 08, 225, 0
J5P1 tail-body / P6 vertical-fintape-edge0, 220, 00, 250, 0

Paper and tools

Use 1 uncoated US Letter sheet, 215.9 × 279.4 mm, at your selected 75 g/m² weight.

Paper source: HP Office20 · US Letter · 75 g/m² · 500 sheets at Staples. Confirm delivery and availability for your address before buying.

Check the package for the sheet size and weight. For this recipe: ruler + pencil · scissors · tape for assembly.

Tape is used for the documented joins. Joint fit and strength remain unverified; inspect the assembled parts before any trial.

Optional analytics

Google Analytics is off. It measures site visits, navigation and generic workshop actions. Personal inputs, account identifiers and private design contents are excluded.

Turning it off stops future analytics and removes this site's Google Analytics cookies. It cannot recall data already sent.