P1 twin-boom-left
Local cut vertices (u, v), mm: 1: (0, 0); 2: (6, 0); 3: (6, 250); 4: (0, 250).
Edges in vertex order, mm: 6, 250, 6, 250.
Assembly vertices (x, y, z), mm: 1: (-22, 0, 0); 2: (-16, 0, 0); 3: (-16, 250, 0); 4: (-22, 250, 0).
Learning Center
Two parallel full-length booms support the main wing and bridge to a tailplane; small rear fins complete this layout.
YOUR PAPER AIRPLANE
Connect two long body strips to a shared rear tail and add a small fin to each strip.
Experimental 3D guide. FlightHub has not physically tested this pattern’s folding or flight.
The 3D view is not a cutting template. These drawings give nominal outlines and joining coordinates in millimeters; they resize to fit this screen. The coordinates are software-checked, but physical fit and a learner-tested join order are unverified.
For an offline copy and standalone SVG files, keep this design in Studio and download its guide. If printing cut sheets, use 100% size and measure the 50 mm scale bar before cutting. Print scale, paper fit, joint strength and flight remain physically unverified.
8 parts on 1 checked US Letter sheet. Each cut outline is a rigid unfolding of the same part shown in the assembly. Dimensions are nominal geometric targets; paper thickness, tape, joint fit and strength remain unverified. No calibrated slot width or flight setting is specified.
Use the separate SVG cut-sheet files at 100% size and measure their 50 mm bars. Part views and assembly views below may be enlarged; use their written dimensions and coordinates.
| Part | Role | Sheet | Cut bounds (mm) |
|---|---|---|---|
| P1 twin-boom-left | boom | 1 | 6, 250 |
| P2 twin-boom-right | boom | 1 | 6, 250 |
| P3 twin-boom-wing-left | main-wing | 1 | 83.486, 35.434 |
| P4 twin-boom-wing-right | main-wing | 1 | 83.486, 35.434 |
| P5 twin-boom-tail-left | tail | 1 | 24.865, 17.71 |
| P6 twin-boom-tail-right | tail | 1 | 24.865, 17.71 |
| P7 twin-boom-fin-left | fin | 1 | 28, 15 |
| P8 twin-boom-fin-right | fin | 1 | 28, 15 |
For each part, mark vertex 1, then the remaining local (u, v) coordinates in millimeters and join them in numbered order. The edge lengths are a cross-check; the bounding rectangle alone is not the part shape.
Local cut vertices (u, v), mm: 1: (0, 0); 2: (6, 0); 3: (6, 250); 4: (0, 250).
Edges in vertex order, mm: 6, 250, 6, 250.
Assembly vertices (x, y, z), mm: 1: (-22, 0, 0); 2: (-16, 0, 0); 3: (-16, 250, 0); 4: (-22, 250, 0).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (6, 0); 3: (6, 250); 4: (0, 250).
Edges in vertex order, mm: 6, 250, 6, 250.
Assembly vertices (x, y, z), mm: 1: (16, 0, 0); 2: (22, 0, 0); 3: (22, 250, 0); 4: (16, 250, 0).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (79.246, 0); 3: (83.486, 23.623); 4: (6.36, 35.434).
Edges in vertex order, mm: 79.246, 24, 78.026, 36.
Assembly vertices (x, y, z), mm: 1: (0, 92, 0); 2: (-78, 106, 0); 3: (-78, 130, 0); 4: (0, 128, 0).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (79.246, 0); 3: (83.486, 23.623); 4: (6.36, 35.434).
Edges in vertex order, mm: 79.246, 24, 78.026, 36.
Assembly vertices (x, y, z), mm: 1: (0, 92, 0); 2: (78, 106, 0); 3: (78, 130, 0); 4: (0, 128, 0).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (22.361, 0); 3: (24.865, 13.774); 4: (3.22, 17.71).
Edges in vertex order, mm: 22.361, 14, 22, 18.
Assembly vertices (x, y, z), mm: 1: (0, 218, 0); 2: (-22, 222, 0); 3: (-22, 236, 0); 4: (0, 236, 0).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (22.361, 0); 3: (24.865, 13.774); 4: (3.22, 17.71).
Edges in vertex order, mm: 22.361, 14, 22, 18.
Assembly vertices (x, y, z), mm: 1: (0, 218, 0); 2: (22, 222, 0); 3: (22, 236, 0); 4: (0, 236, 0).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (28, 0); 3: (28, 15); 4: (0, 15).
Edges in vertex order, mm: 28, 15, 28, 15.
Assembly vertices (x, y, z), mm: 1: (-18, 218, 0); 2: (-18, 246, 0); 3: (-18, 246, 15); 4: (-18, 218, 15).
Local cut vertices (u, v), mm: 1: (0, 0); 2: (28, 0); 3: (28, 15); 4: (0, 15).
Edges in vertex order, mm: 28, 15, 28, 15.
Assembly vertices (x, y, z), mm: 1: (18, 218, 0); 2: (18, 246, 0); 3: (18, 246, 15); 4: (18, 218, 15).
Assembly coordinates in millimeters: x left/right, y rearward from the body nose (or the shown center datum), z up. Cut drawings use their own numbered vertex coordinates. Match the listed edge or overlap endpoints. Tape tabs join those locations; the layout does not prescribe an adhesive product, tape size or verified load capacity.
| Join | Parts | Method | Endpoint A (x, y, z), mm | Endpoint B (x, y, z), mm |
|---|---|---|---|---|
| J1 | P1 twin-boom-left / P3 twin-boom-wing-left | tape-overlap | -16, 94.872, 0 | -22, 128.564, 0 |
| J2 | P1 twin-boom-left / P5 twin-boom-tail-left | tape-overlap | -22, 236, 0 | -16, 220.909, 0 |
| J3 | P1 twin-boom-left / P7 twin-boom-fin-left | tape-edge | -18, 218, 0 | -18, 246, 0 |
| J4 | P2 twin-boom-right / P4 twin-boom-wing-right | tape-overlap | 22, 128.564, 0 | 16, 94.872, 0 |
| J5 | P2 twin-boom-right / P6 twin-boom-tail-right | tape-overlap | 22, 236, 0 | 16, 220.909, 0 |
| J6 | P2 twin-boom-right / P8 twin-boom-fin-right | tape-edge | 18, 218, 0 | 18, 246, 0 |
| J7 | P3 twin-boom-wing-left / P4 twin-boom-wing-right | tape-edge | 0, 92, 0 | 0, 128, 0 |
| J8 | P5 twin-boom-tail-left / P6 twin-boom-tail-right | tape-edge | 0, 218, 0 | 0, 236, 0 |
| J9 | P5 twin-boom-tail-left / P7 twin-boom-fin-left | tape-edge | -18, 221.273, 0 | -18, 236, 0 |
| J10 | P6 twin-boom-tail-right / P8 twin-boom-fin-right | tape-edge | 18, 221.273, 0 | 18, 236, 0 |
Use 1 uncoated US Letter sheet, 215.9 × 279.4 mm, at your selected 75 g/m² weight.
Paper source: HP Office20 · US Letter · 75 g/m² · 500 sheets at Staples. Confirm delivery and availability for your address before buying.
Check the package for the sheet size and weight. For this recipe: ruler + pencil · scissors · tape for assembly.
Tape is used for the documented joins. Joint fit and strength remain unverified; inspect the assembled parts before any trial.