3D printed RC aircraft · Revision 0.2.1 · Bench review
Raven Switchwing
A tricopter with two tilting front motors, a fixed rear lift rotor and a removable aft module.
The latest bench CAD is shown in the preview. The build guide and member kit use 0.2.1.
- Wingspan
- 1,170 mm
- Wing section
- NACA 2412
- Configuration
- Front-tilt tricopter
Illustrated guide, bill of materials, STLs and Bambu Studio projects in one ZIP.
Loading the 3D view…
Exploded view inventoryHatch keeper bench candidate
- Airframe
- The 0.2.1 tilt-rotor assembly with the trial forward-hatch keeper and mounting shoe.
- Fasteners and linkages
- Collars, seam catches, aft-keel hardware, motor screw locations and the M2 hatch keeper screw and square nut references.
- Electronics and wiring
- Propulsion and tilt hardware, ESCs, flight controller, battery, receiver, GNSS, servos and schematic harness routing.
- Items to check in the build guide
- Confirm keeper screw engagement, tilt-shaft retention and propeller retainers. The bill of materials covers the airspeed kit, power distribution and current sensor.
A tilt-rotor aircraft with a serviceable aft module
- Airframe
- Sectional wings with moving ailerons flank a center battery bay. The forward hatch opens while the aft deck stays seated. Quarter-turn collars align the fuselage modules, and a separate keel lock retains the V-tail module.
- How it’s controlled
- Matek H743-WING V3 and ArduPlane QuadPlane. Three motor ESCs, two tilt servos, two aileron servos and two ruddervator servos. Flight settings await measurements.
- Who it’s for
- For RC builders checking tilt travel, quarter-turn fuselage joints and removable equipment before powered bench work.
- Flight targets
- No range, speed or altitude targets are published for this revision.
Physical checks are pending for print fit, retention, installed power, mass and balance, hover, both transitions, and landing.
Print files
The member build kit contains the listed STLs and print setup. Start with the joint coupons and record the measured fit before selecting an interface for the bench assembly.
Print setup
- Bambu Lab P1S with a 0.4 mm nozzle. Start with the saved 0.15, 0.25 and 0.35 mm clearance coupon projects. The coupon profiles use Generic PETG on textured PEI at 0.20 mm layers, four walls and 30% gyroid. The 6 editable airframe plates were checked with Bambu Studio 02.09.01.70. Verify material, bed, supports and orientation on your own printer. Record the physical print, fit, retention, mass and balance before applying power.
View the 69 printed parts
Images show the exported meshes for this revision. Each part is shown at its own scale.
| Part and STL filename | Image | Quantity | Material |
|---|---|---|---|
Removable nose shellparts/airframe/nose-shell.stl | ![]() | 1 | LW-PLA candidate |
Center shell front seat ringparts/airframe/center-shell-front-ring.stl | ![]() | 1 | LW-PLA candidate |
Center rear seat with upper keel accessparts/airframe/center-shell-rear-ring.stl | ![]() | 1 | LW-PLA candidate |
Open-top center shellparts/airframe/center-shell.stl | ![]() | 1 | LW-PLA candidate |
Lift-off front battery hatchparts/airframe/center-hatch.stl | ![]() | 1 | LW-PLA candidate |
Removable aft shellparts/airframe/aft-shell.stl | ![]() | 1 | LW-PLA candidate |
nose collar spigot saddleparts/airframe/nose-spigot-saddle.stl | ![]() | 1 | PETG candidate |
nose fixed receiver saddleparts/airframe/nose-receiver-saddle.stl | ![]() | 1 | PETG candidate |
aft collar spigot saddleparts/airframe/aft-spigot-saddle.stl | ![]() | 1 | PETG candidate |
aft fixed receiver saddleparts/airframe/aft-receiver-saddle.stl | ![]() | 1 | PETG candidate |
Battery tray with four 12 × 3.5 mm strap slotsparts/airframe/battery-tray.stl | ![]() | 1 | PETG candidate |
Flight controller deckparts/airframe/avionics-deck.stl | ![]() | 1 | PETG candidate |
GNSS roof trayparts/airframe/gnss-deck.stl | ![]() | 1 | PETG candidate |
Aft ESC elevated bench deckparts/airframe/aft-esc-deck.stl | ![]() | 1 | PETG candidate |
port wing panel 1parts/airframe/port-wing-1.stl | ![]() | 1 | LW-PLA candidate |
port wing panel 2parts/airframe/port-wing-2.stl | ![]() | 1 | LW-PLA candidate |
port aileron 2parts/airframe/port-aileron-2.stl | ![]() | 1 | LW-PLA candidate |
port wing panel 3parts/airframe/port-wing-3.stl | ![]() | 1 | LW-PLA candidate |
port aileron 3parts/airframe/port-aileron-3.stl | ![]() | 1 | LW-PLA candidate |
port ESC elevated bench deckparts/airframe/port-esc-deck.stl | ![]() | 1 | PETG candidate |
port nacelle base plateparts/airframe/port-nacelle-foot.stl | ![]() | 1 | PETG candidate |
port tilt bearing support 1parts/airframe/port-tilt-bearing-1.stl | ![]() | 1 | PETG candidate |
port tilt bearing support 2parts/airframe/port-tilt-bearing-2.stl | ![]() | 1 | PETG candidate |
port tilting motor plateparts/airframe/port-tilt-motor-plate.stl | ![]() | 1 | PETG candidate |
port pivot trunnionparts/airframe/port-tilt-trunnion.stl | ![]() | 1 | PETG candidate |
port tilt servo trayparts/airframe/port-tilt-servo-tray.stl | ![]() | 1 | PETG candidate |
port canted tail panelparts/airframe/port-vtail.stl | ![]() | 1 | LW-PLA candidate |
port ruddervatorparts/airframe/port-ruddervator.stl | ![]() | 1 | LW-PLA candidate |
port aileron servo trayparts/airframe/port-aileron-tray.stl | ![]() | 1 | PETG candidate |
port landing skidparts/airframe/port-skid.stl | ![]() | 1 | PETG candidate |
starboard wing panel 1parts/airframe/starboard-wing-1.stl | ![]() | 1 | LW-PLA candidate |
starboard wing panel 2parts/airframe/starboard-wing-2.stl | ![]() | 1 | LW-PLA candidate |
starboard aileron 2parts/airframe/starboard-aileron-2.stl | ![]() | 1 | LW-PLA candidate |
starboard wing panel 3parts/airframe/starboard-wing-3.stl | ![]() | 1 | LW-PLA candidate |
starboard aileron 3parts/airframe/starboard-aileron-3.stl | ![]() | 1 | LW-PLA candidate |
starboard ESC elevated bench deckparts/airframe/starboard-esc-deck.stl | ![]() | 1 | PETG candidate |
starboard nacelle base plateparts/airframe/starboard-nacelle-foot.stl | ![]() | 1 | PETG candidate |
starboard tilt bearing support 1parts/airframe/starboard-tilt-bearing-1.stl | ![]() | 1 | PETG candidate |
starboard tilt bearing support 2parts/airframe/starboard-tilt-bearing-2.stl | ![]() | 1 | PETG candidate |
starboard tilting motor plateparts/airframe/starboard-tilt-motor-plate.stl | ![]() | 1 | PETG candidate |
starboard pivot trunnionparts/airframe/starboard-tilt-trunnion.stl | ![]() | 1 | PETG candidate |
starboard tilt servo trayparts/airframe/starboard-tilt-servo-tray.stl | ![]() | 1 | PETG candidate |
starboard canted tail panelparts/airframe/starboard-vtail.stl | ![]() | 1 | LW-PLA candidate |
starboard ruddervatorparts/airframe/starboard-ruddervator.stl | ![]() | 1 | LW-PLA candidate |
starboard aileron servo trayparts/airframe/starboard-aileron-tray.stl | ![]() | 1 | PETG candidate |
starboard landing skidparts/airframe/starboard-skid.stl | ![]() | 1 | PETG candidate |
Aft lift front bulkheadparts/airframe/aft-lift-front-bulkhead.stl | ![]() | 1 | PETG candidate |
Aft lift rear bulkheadparts/airframe/aft-lift-rear-bulkhead.stl | ![]() | 1 | PETG candidate |
Fixed aft lift motor plateparts/airframe/aft-lift-plate.stl | ![]() | 1 | PETG candidate |
Removable rear keel pin access coverparts/airframe/aft-keel-service-cover.stl | ![]() | 1 | LW-PLA candidate |
Aft harness fixed strain-relief bracketparts/airframe/aft-service-fixed-clip.stl | ![]() | 1 | PETG candidate |
Aft harness moving strain-relief bracketparts/airframe/aft-service-moving-clip.stl | ![]() | 1 | PETG candidate |
port rail seat for battery tray X146parts/airframe/port-battery-tray-seat-146.stl | ![]() | 1 | PETG candidate |
port rail seat for battery tray X247parts/airframe/port-battery-tray-seat-247.stl | ![]() | 1 | PETG candidate |
starboard rail seat for battery tray X146parts/airframe/starboard-battery-tray-seat-146.stl | ![]() | 1 | PETG candidate |
starboard rail seat for battery tray X247parts/airframe/starboard-battery-tray-seat-247.stl | ![]() | 1 | PETG candidate |
Fixed aft center cover under GNSS deckparts/airframe/center-hatch-aft.stl | ![]() | 1 | LW-PLA candidate |
Spigotparts/coupons/switchwing-c15-spigot.stl | ![]() | 1 | PETG candidate |
Receiverparts/coupons/switchwing-c15-receiver.stl | ![]() | 1 | PETG candidate |
Collarparts/coupons/switchwing-c15-collar.stl | ![]() | 1 | PETG candidate |
Keeperparts/coupons/switchwing-c15-keeper.stl | ![]() | 1 | PETG candidate |
Spigotparts/coupons/switchwing-c25-spigot.stl | ![]() | 1 | PETG candidate |
Receiverparts/coupons/switchwing-c25-receiver.stl | ![]() | 1 | PETG candidate |
Collarparts/coupons/switchwing-c25-collar.stl | ![]() | 1 | PETG candidate |
Keeperparts/coupons/switchwing-c25-keeper.stl | ![]() | 1 | PETG candidate |
Spigotparts/coupons/switchwing-c35-spigot.stl | ![]() | 1 | PETG candidate |
Receiverparts/coupons/switchwing-c35-receiver.stl | ![]() | 1 | PETG candidate |
Collarparts/coupons/switchwing-c35-collar.stl | ![]() | 1 | PETG candidate |
Keeperparts/coupons/switchwing-c35-keeper.stl | ![]() | 1 | PETG candidate |
P1S plate setup and orientation
Bambu Studio 02.09.01.70 sliced 6 airframe plates with 3,743 total layers. Estimated filament use is 941.9 g across the airframe plates, including supports and brims. The 3 fit-coupon projects are separate.
All airframe and coupon plates completed without plate warnings.
View the verified P1S plate layouts



Workshop tools
Use your existing workshop equipment where suitable. The reference printer and these tools are budgeted separately.
- Bambu Lab P1S and calipers: Stock 0.4 mm nozzle; log printer, slicer, filament lot, orientation and measured dimensions bench equipment Reference for Bambu Lab P1S and calipers
- Guarded thrust rig and logging instruments: Remote power isolation plus thrust load cell and current voltage RPM temperature instrumentation; use separate rigid stand and physical prop guard bench equipment
Bill of materials
Aircraft parts, assembly supplies, and radio and charging gear for revision 0.2.1.
Printed-part images show the exported meshes. Hardware and supply drawings help identify items. Images are not to scale.
Download BOM (CSV)Scroll each table sideways to see specifications and supplier links.
Printed parts and filament11 items
| Item | Image | Qty | Price (USD) and stock | Specification & sourcing |
|---|---|---|---|---|
| Switchwing quarter-turn fit coupons | Nominal c25 spigot | 1 set | Print from the kit | Print the matching collar and catch variants in the intended bulkhead material on a 0.4 mm P1S; log each coupon gap and engagement print first |
| Fuselage shells and battery hatch | Lift-off front battery hatch | 1 assembly | Print from the kit | Use the 0.2.1 forward access hatch and fixed aft deck. Confirm seating, clearance and retention with the exact print profiles. prototype CAD |
| Keyed bulkheads and quarter-turn collars | nose fixed receiver saddle | 2 interfaces | Print from the kit | Reinforced locating shoulders and removable keyed cam collars; independent captive catch on both seams prototype CAD |
| Left and right wings and ailerons | port wing panel 1 | 1 assembly | Print from the kit | Sectional shells with spar seats; hinge and servo hardpoints require coupon and pullout checks prototype CAD |
| V-tail and ruddervators | port canted tail panel | 1 assembly | Print from the kit | Mirrored moving ruddervators and retained hinges; envelope and load review required prototype CAD |
| Tilt nacelles and rear motor seat | port tilting motor plate | 3 assemblies | Print from the kit | Two bearing-supported front yokes plus fixed aft lift seat tied to internal frame; printed shells require a separate structural review prototype CAD |
| Servo and equipment trays plus skids | port tilt servo tray | 1 set | Print from the kit | Separate adjustable battery tray and mechanical battery straps; ventilated ESC and controller access prototype CAD |
| Lightweight shell filament | 1 lot | $27.88 743.661 g at $0.037/g $29.99 / 800 g spool In stock Recheck stock · In stock at last check | Provisional LW-PLA class; exact product and shell profile to be qualified for mass and layer strength material pending Gray 1.75 mm PolyLite LW-PLA 800 g spool PA08003 is available. The 743.661 g amount is the released slicer estimate for this material candidate. | |
| Rigid airframe filament (PETG) | 1 lot | $3.77 198.277 g at $0.019/g $18.99 / 1000 g spool In stock Recheck stock · In stock at last check | Use the saved Generic PETG airframe projects as the process reference. Choose and record the actual PETG spool. The three fit coupon projects have separate material estimates. material candidate Black 1.75 mm PETG HF 1 kg spool G02-K0-1.75-1000-SPL shows in stock. Budget uses the released Generic PETG slicer estimate for this material candidate. | |
| Battery-tray rail seats | port rail seat for battery tray X146 | 4 | Print from the kit | Four PETG candidate rail seats with nominal Ø9.3 mm bores. Bond to the battery-tray edges with the bores clear and review actual alignment, adhesive selection and load retention. Successor bench CAD |
| Aft service cover and harness strain-relief brackets | Removable rear keel pin access cover | 1 set | Print from the kit | Print one rear cover and two candidate brackets. Check cover retention, actual wire restraints and access to both connector positions. Successor bench CAD |
Propulsion and onboard electronics13 items
| Item | Image | Qty | Price (USD) and stock | Specification & sourcing |
|---|---|---|---|---|
| EMAX ECO II 2807 1700 KV motor | 3 | $19.49 / motor 3 × $19.49 = $58.47 In stock Recheck stock · In stock at last check | Four M3 mounting points on a 19 × 19 mm square; M5 prop nut; verify supplied screws and shaft engagement sourced candidate The 1700 KV ECO228071700 variant is in stock. The retailer's product inventory lists 83 units for this variant, enough for the three required motors. | |
| HQProp DP7X4X3GR-PC | 1 set | $3.74 / 4-pack In stock Recheck stock · In stock at last check | Two CW and two CCW per set; use three with handedness verified on the reviewed motor map; 177.8 mm diameter and 5 mm bore sourced candidate The light gray DP7X4X3GR-PC four-pack is in stock at the listed sale price and includes two CW and two CCW props. | |
| Hobbywing FlyFun 60A V5 ESC | 3 | $49.99 / ESC 3 × $49.99 = $149.97 Out of stock Recheck stock · Out of stock at last check | 3–6S LiPo, 60 A continuous vendor rating, 69 × 35 × 18 mm and 73 g each; isolate each ESC BEC output sourced candidate Exact 3–6S FlyFun 60A V5 model 30214101 is sold out at the US manufacturer storefront. Three ESCs are required. | |
| Tattu FunFly 4S 1550 mAh XT60 LiPo | 1 | $20.59 / battery In stock Recheck stock · In stock at last check | TA-FF15504SP / TAA15504S10X6. Nominal 72 × 35 × 36 mm and 178 ± 20 g. The CAD fit gauge is 77 × 37 × 38 mm. Verify actual fit, balance, voltage sag, integrated current and connector temperature. Candidate pack for revision 0.2.1. Measure the delivered pack and verify the installed electrical load before use. The FunFly 4S 1550 mAh XT60 pack TAA15504S10X6 / TA-FF15504SP shows in stock. | |
| Main DC distribution and current sensor | 1 set | Source to choose | Separate from FC board power traces; rated pack connector and harness sized from guarded single-branch and integrated measurements release blocked The released bill of materials leaves the ratings and part selection to measured current and connector fit. | |
| Castle CC BEC Pro 010-0004-01 | 1 | $52.95 / regulator In stock Recheck stock · In stock at last check | Separate regulated servo rail programmed to a provisional 5.5 V; qualify loaded ripple and temperature sourced candidate Model 010-0004-01 shows in stock. The listing is for one regulator. The Castle Link programmer is a separate purchase. | |
| Matek H743-WING V3 | 1 | $204.99 / flight controller In stock Recheck stock · In stock at last check | ArduPlane MATEKH743 target; segregate FC electronics power from external servo positive rail; record exact board and firmware sourced candidate The retailer lists the Matek H743-WING V3 under SKU QRC-1110 as in stock. RaceDayQuads and ProgressiveRC showed the V3 sold out at their lower listed prices. | |
| Hitec D645MW 36645S | 2 | $49.99 / servo 2 × $49.99 = $99.98 In stock · Required quantity unconfirmed Recheck stock · In stock at last check | Independent left/right tilt actuators, 40.8 × 19.8 × 37.8 mm body, 25T spline; no-load and loaded travel require review sourced candidate Hitec shows exact SKU 36645S in stock. The public listing does not expose a count for the two required servos. | |
| Hitec HS-5085MG | 4 | $48.99 / servo 4 × $48.99 = $195.96 In stock · Required quantity unconfirmed Recheck stock · In stock at last check | Two ailerons and two ruddervators, 29.0 × 13.0 × 29.4 mm body and 24T spline; envelope excludes horn/lead travel sourced candidate Hitec shows exact SKU 35085S in stock. The public listing does not expose a count for the four required servos. | |
| RadioMaster RP3 V2 ELRS 2.4 GHz receiver | 1 | $19.99 / receiver In stock Recheck stock · In stock at last check | Dual antenna serial receiver with CRSF wired to a full UART; separate antennas from carbon and power wiring sourced candidate The RP3 V2 2.4 GHz ExpressLRS FCC variant HP0157.RX-RP3-V2 is available. | |
| Holybro M10 GPS IST8310 6-pin 12042 | 1 | $43.99 / GNSS module In stock Recheck stock · In stock at last check | UART GNSS plus I2C compass; repin a documented harness to controller and check supply and orientation sourced candidate The storefront marks the IST8310 secondary 6-pin variant 12042 available and publishes 59 units. | |
| Matek ASPD-DLVR airspeed kit | 1 | $131.99 / sensor Out of stock Recheck stock · Out of stock at last check | Digital differential-pressure sensor and supplied pitot tubing; reserve pitot placement outside rotor wash and verify sensor plumbing sourced candidate The exact ASPD-DLVR sensor listing SKU 14238 shows zero stock. The retailer lists the sensor and does not confirm pitot accessories. | |
| Removable aft service harness and connector pair | 1 set | Source to choose | Provide separately rated power and signal connectors at the fixed and moving locations shown by the fit envelopes. Verify polarity, pinout, cable ratings and strain relief for the measured aft branch. Electrical selection and fit pending The released bill of materials leaves the connector pair, current rating and fit to the exact assembly. |
Airframe stock and linkages5 items
| Item | Image | Qty | Price (USD) and stock | Specification & sourcing |
|---|---|---|---|---|
| Carbon main spar and central frame stock | 1 set | Source to choose | Source straight carbon stock. Use two nominal Ø9 mm OD / Ø7 mm ID × 175 mm center rails at CAD X134–309 and the shortened Ø19 mm OD / Ø16 mm ID aft stock at X384–509. Verify actual tube fits, grade and structural load before use. source pending The released bill of materials specifies tube dimensions and calls for fit, grade and structural load verification before selecting the complete set. | |
| Metal tilt shafts and axial retainers | 2 sets | Source to choose | Start from the 6 mm nominal shaft witness and select a ground shaft with positive axial retention. Final length and material await bearing and linkage fit. source pending Final shaft length, material and retention depend on the exact bearing and linkage fit. | |
| NMB LF-1360ZZRA5P58L0 flanged pivot bearings | 4 | Price unconfirmed Stock unconfirmed | Two per nacelle, 6 mm bore, 13 mm body, 5 mm width and 15 mm flange. Fit candidate for a separate retained bearing seat. sourced candidate The manufacturer confirms the exact bearing specification. A USD seller listing with price and stock for this exact part number could not be verified. | |
| Fasteners hinges horns and linkages | 1 set | Source to choose | Fit fasteners and thread engagement to actual metal hardpoints. Use metal horns, retained links and verified control hinges. source pending Fastener, hinge and linkage selections depend on exact metal hardpoints and thread engagement. | |
| Metal keel socket, tongue, ties and aft stock bridge | 1 set | Source to choose | CAD models an 11 × 5 mm tongue with 17.9 mm nominal engagement, two center rail clamps and diagonal ties, and a rear clamp and stop on the 19 × 16 mm aft tube from X384 to X509. Resolve actual metal grade, fastening, clamp details and structural loads with the exact assembly. Fabrication and load qualification pending This is a fabrication and load-qualified assembly. The released bill of materials has no selected retail set. |
Fasteners and assembly supplies3 items
| Item | Image | Qty | Price (USD) and stock | Specification & sourcing |
|---|---|---|---|---|
| Captive seam catches and collar hardware | 2 sets | Source to choose | Mechanical secondary lock and visible position mark per seam; material and rated load TBD source pending Hardware materials, rated load and exact retail items are pending. | |
| Battery straps pads and connector restraint | 1 set | Source to choose | Two independent pack restraints and a positive axial stop. Check the exact tray slot spacing, strap fit, XT60 access and lead bends. source pending The complete kit depends on measured tray slot spacing, strap fit and connector clearance. | |
| Aft keel retention pin, keeper and tongue fasteners | 1 pin set and 2 M3 fasteners | Source to choose | Separate Ø3 mm clevis pin and keeper, plus two M3 fasteners at the moving tongue seat. Check exact grip, axial retention, thread engagement and keeper access on the physical article. Sourced hardware fit pending Final 3 mm pin grip, keeper access and M3 fastener lengths depend on physical fit. |
Radio and charging gear2 items
| Item | Image | Qty | Price (USD) and stock | Specification & sourcing |
|---|---|---|---|---|
| RadioMaster Boxer ELRS 2.4 GHz radio | 1 | $153.99 / transmitter In stock Recheck stock · In stock at last check | Select the internal 2.4 GHz ExpressLRS version; region and matching receiver firmware checked before bench use sourced candidate The current Boxer M2 internal 2.4 GHz ELRS FCC variant HP0157.0043-M2 is available. The price covers the transmitter package. The radio battery is separate. | |
| 4S balance charger and charge lead | 1 set | Source to choose | Use an approved 4S balance charger and a matching XT60 charge lead. Confirm pack and charger limits with the delivered hardware. bench equipment The released bill of materials leaves the compatible charger and matching XT60 charge lead unselected. |
Build guide
A front-tilt tricopter with a removable aft keel and a revised center battery bay. The forward hatch gives access to a shorter XT60 candidate pack while the aft deck stays seated.
Bambu Lab P1S with a 0.4 mm nozzle. Start with the saved 0.15, 0.25 and 0.35 mm clearance coupon projects. The coupon profiles use Generic PETG on textured PEI at 0.20 mm layers, four walls and 30% gyroid. The 6 editable airframe plates were checked with Bambu Studio 02.09.01.70. Verify material, bed, supports and orientation on your own printer. Record the physical print, fit, retention, mass and balance before applying power. Review the print inventory and bill of materials before starting. Use the 3D assembly reference to find parts on the aircraft. The plate images show how parts sit on the printer bed.
Explore the assembly, exploded view and components in 3D
Open full-window 3D referenceCompare the assembled and exploded views alongside the guide. Select Wiring to inspect the candidate harness routes. Select Installed joint service to review the access and removal steps on the full airframe. Select Battery service to inspect the hatch, plug and pack withdrawal.
Connection checks
- Keyed shoulders and quarter-turn collars
- Use the fit coupons to measure seating before assembling the airframe. Seat the keyed spigots at the hard stops, rotate each collar to its lock mark and engage its positive lock pin. Check both seams for movement, cracks and wires entering the collar path.
- Aft keel and service jumper
- With the propellers removed and battery disconnected, remove the aft service cover and unplug both jumper ends. Release the separate aft keel pin and collar pin before turning the collar and withdrawing the aft module. On reassembly, check both keepers and strain relief before reconnecting the jumper.
- Battery tray and rail seats
- Dry-fit both center rails and all four tray seats. Check the bond surfaces, open bores, both strap paths and end restraints with an inert pack gauge. Confirm the delivered pack, plugs and balance lead can lift out through the forward hatch while the aft deck remains seated.
- Tilting nacelle pivots and retainers
- Check each metal shaft, bearing, motor plate, actuator link and axial retainer against the actual hardware. With power disconnected, sweep an inert propeller template through the complete tilt range and measure backlash, stop clearance and left-right mismatch.
- Wing, tail and fixed lift hardpoints
- Dry-fit the main spar, wing carriers, tail supports, skids and rear lift mount to the structural frame. Record fastener engagement, hinge retention and free aileron and ruddervator travel. Check that service motion and control motion keep clear of wiring and rotor envelopes.
Print and measure the fit coupons
- Why this matters
- The bayonet interfaces need measurable alignment, deliberate release and independent keeper engagement.
- Where to look
- Find the collar, spigot and catch parts on the exact P1S coupon projects. Read support settings before printing.

- Print the collar, key and catch coupons on the P1S with a 0.4 mm nozzle in the exact candidate material and orientation.
- Record the profile, material lot, measured gap, edge step, play and insertion effort. Keep the coupon ID paired with each result.
- Check that the secondary catch engages only at the visible lock mark and releases deliberately. Compare fit before and after repeated cycles.
Before you continue
Record seating, quarter-turn feel, lock-mark alignment and keeper engagement for each clearance before choosing a fit.
Show reference images for this step

Dry-fit the nose, center and aft modules
- Why this matters
- The module shoulders, center rails and battery installation share a tight center frame.
- Where to look
- Follow the wing-spar carry-throughs above the pack tray. Identify the removable forward hatch, fixed aft deck, straps and connector access.

- Seat the keyed nose spigot on the hard stop, rotate the collar to its lock position and install its positive lock pin. Start with the isolated coupon to measure seating and insertion effort before attempting the exact assembled airframe.
- Inspect both seams for even seating, cracking, unexpected movement and wires entering the collar path. The aft keel retention pin and the original collar lock pin both need independent retention.
- Dry-fit the two 175 mm center rails and the four battery-tray rail seats. Bond the seats to the tray edges and keep the nominal Ø9.3 mm seat bores clear. Confirm actual strap-slot access, pack clearance and fit of the repositioned servo regulator before power.
- Keep the fixed aft deck seated and lift the forward hatch 30 mm in the modeled access pose. Start with an inert 77 × 37 × 38 mm fit gauge. Measure the delivered pack, leads and plugs before using the actual pack.
- Dry-fit both straps at CAD X181 and X218 mm. The modeled slots accept straps up to 10 mm wide. Confirm actual strap grip, soft end pads and positive axial restraint with both wing spars fitted.
- Disconnect and park the XT60 and balance leads before releasing both straps. Lift the pack and its leads straight up. The CAD check uses 72 mm of travel. Check access, strain relief and harness clearance on the physical assembly.
Before you continue
Measure delivered pack and connector clearance through the full access path, then check positive restraint with both spars fitted.
Show reference images for this step

Service the installed aft keel and collar
- Why this matters
- The separate metal keel and original collar each need positive retention. Service access requires both releases in the modeled order.
- Where to look
- Open Installed joint service and locate the aft cover, disconnectable jumper, keel pin and collar lock.

- Remove the propellers and disconnect the flight battery. Lift the dedicated aft keel service cover straight up and remove it. The modeled access pose raises it 24 mm. Confirm actual tool access and isolate every branch before touching the service harness.
- Unplug and remove the aft service jumper at the fixed and moving connector ends. Restrain each remaining harness section on its own module. Check actual wire bends and clearance through both motion paths.
- Withdraw the separate Ø3 mm aft keel retention pin at X329. The nominal CAD service pose raises it 15 mm. Then withdraw the original collar lock pin 6 mm, rotate the collar 90 degrees and slide the complete aft module straight aft along the nominal 18 mm CAD path. Stop if the printed assembly binds.
- Reassemble in reverse order. Verify hard-stop seating and both independent keepers before reconnecting the jumper. Verify actual pin grip, connector polarity, pinout and strain relief before refitting the cover or powering up.
Before you continue
Verify physical pin grip and travel, keep both harness branches restrained, and confirm both keepers before reconnecting the jumper.
Fit the load-bearing frame and tail
- Why this matters
- The carbon stock, keel and tailored fittings carry loads from the wing and tail back into the center structure.
- Where to look
- Use the exploded view to locate the center rails, rear stock bridge, wing supports and V-tail attachments.
- Fit the main spar, wing carriers, tail supports and skids to the reinforced frame. Record fastener engagement and fit at each hardpoint.
- Fit the rear fixed lift motor mount to the structural frame and inspect the tail clearance using an inert propeller sweep template.
- Fit the two ailerons and two ruddervators. Check hinge retention, linkage access and measured free travel.
Before you continue
Review metal fitting material and fastening, carbon engagement, fastener grip and control travel before loading the structure.
Assemble the front tilt nacelles
- Why this matters
- The two front tilt stations need compatible axial retention and matched travel.
- Where to look
- Identify each metal pivot, flanged bearing, actuator link and travel stop in the front nacelles.
- Fit each supported metal pivot, motor plate, actuator link and positive axial retainer. Confirm the bearing and shaft fits against actual hardware samples.
- With the battery disconnected, use a 177.8 mm inert sweep template to check both front clearances through the full physical range, including beyond vertical.
- With propellers removed, measure the left and right travel, stop clearance, backlash and actuator mismatch. Review loaded authority before choosing servo endpoints.
Before you continue
Measure both endpoints, stop clearance, backlash and actuator mismatch with propellers off.
Mount electronics and route the harness
- Why this matters
- Independent servo and propulsion supplies need defined isolation and access at the removable rear harness.
- Where to look
- Trace the controller, three ESCs, dedicated servo supply and fixed/moving jumper ends in the wiring worksheet.

- Mount the flight controller, receiver, air data, three ESCs and dedicated servo regulator where cooling and service access can be inspected.
- S1 Motor 1 · starboard front (PWM, function 33) · S2 Motor 2 · port front (PWM, function 34) · S3 Motor 4 · aft fixed (PWM, function 36)
- S7 Port front tilt (PWM, function 75) · S8 Starboard front tilt (PWM, function 76) · S9 Port aileron (PWM, function 4)
- S10 Starboard aileron (PWM, function 4) · S11 Port ruddervator (PWM, function 79) · S12 Starboard ruddervator (PWM, function 80)
- Use the independent servo supply and common signal ground. Isolate its positive rail from the FC and the ESC BECs. Keep the main propulsion current on a separate rated distribution harness.
Before you continue
Inspect connector pinout, strain relief, separate rated paths and cooling access before applying power.
Verify controls, power and failsafe with props off
- Why this matters
- Control and power checks establish direction, shutdown and rail behavior before propulsion testing.
- Where to look
- Use the exact controller output map and confirm front tilt travel separately from wing and tail control travel.
- Check polarity, connector locks, wiring strain relief and rail voltage before enabling any ESC. Check that simultaneous servo movement leaves the FC powered and responsive.
- Verify motor assignment and direction, combined V-tail mixing, tilt synchronization, arm and disarm, and response to signal loss or low voltage.
- Record board firmware, radio settings, motor map, control travel and the configuration used for the test. Review mode and abort behavior with the propellers removed.
Before you continue
Record firmware, motor map, radio failsafe, rail behavior and ground abort behavior with propellers removed.
Measure each propulsion branch on a guarded rig
- Why this matters
- Separate measurements are needed before approving the pack, connector and integrated electrical load.
- Where to look
- Use the guarded stand and remote isolation to measure each front and aft propulsion branch with the selected components.
- Have an experienced operator review the stand, current protection, guard, exclusion area and remote isolation before fitting a propeller.
- Test one exact motor, propeller and ESC branch at a time. Record thrust, current, voltage, RPM, temperature and vibration.
- Review current, wiring and cooling before planning any combined powered check. Stop for structural movement, abnormal vibration, overheating, desynchronization or brownout.
Before you continue
Review measured current, thermal behavior and voltage sag against the exact pack, wiring and connector ratings.
Review balance, hover and transition evidence
- Why this matters
- The measured center of gravity must be reviewed for both the hover thrust triangle and wing-borne balance.
- Where to look
- Use the secured pack location and record both front nacelle positions, rear motor location and flight control configuration.
- Weigh the exact complete assembly and measure its balance with the installed battery. Review projected CG within the hover thrust triangle and the separate fixed-wing balance range.
- Review mechanical retention, thrust reserve, yaw authority and loaded pivot travel before authorizing a controlled hover or landing trial.
- Set airspeed, transition and abort thresholds from Switchwing measurements. Record both directions of transition and keep the flight hold until the exact build passes review.
Before you continue
Confirm the required physical and supervised test evidence before approving hover, landing or transition.
Checks to record
- Record physical print dimensions, both hard-stop seats, fit through the complete aft path, and positive engagement of the collar and aft keel retention pins.
- Measure the delivered Tattu pack and verify hatch access, plug mating, end pads and strap retention. Qualify the exact XT60 pair and harness for measured current, voltage sag and temperature before testing combined loads.
- Record connector identity, polarity, isolation, strain relief and clearance through the complete service sequence.
- Measure loaded tilt and tail control travel, full motor clearance, ESC and servo current, temperature, balance, range and failsafe.
- Record guarded propulsion, hover, both transition directions and landing separately after bench approval.




































































